A tractor pulls a land leveling scraper with a receiver mast across a field at dusk, a laser transmitter on a tripod in the foreground.
Illustrative image

Laser land leveling systems for agriculture

Precision That Levels Up Your Work.

AMALASER systems use a rotating laser to guide your scraper as you drive, so you can shape fields to a precise level or grade and help irrigation water reach every corner. Built for farmers and land leveling contractors.

Request a Quote Book a Demo
  • Transmitter Sets one laser reference over the field
  • Receiver Reads the beam from the scraper mast
  • Control Guides blade height from the cab

01 Why laser leveling

Flat ground.
No guesswork.

When a field is uneven, water pools in the low spots and misses the high ones. AMALASER takes the guesswork out of leveling, so every pass works to the same exact target.

  • 01

    One reference for the whole field

    The laser projects a single, consistent reference plane across the work area. Every pass is measured against it, not judged by eye.

  • 02

    The blade follows the grade

    As you drive, the system reads the beam and signals the hydraulics to raise or lower the scraper. It cuts high spots and fills low ones. confirm automatic / manual modes

  • 03

    Water goes where you intend

    A level or evenly graded surface lets irrigation water advance uniformly across the field, with fewer waterlogged hollows and dry high ground.

  • 04

    Clear from the operator's seat

    In-cab indicators show where the blade sits relative to grade, so the operator can concentrate on driving. confirm display & controls

Editor Accuracy, working range and any water or time savings will be added here once AMALASER supplies verified figures. No performance numbers are shown until then.

Want to know how this applies to your fields?

Request a Quote

02 How AMALASER works

A laser line becomes a level field.

Four parts work as one loop: the transmitter sets the target, the receiver measures against it, the control box decides and the hydraulics act.

Laser land leveling system diagram A transmitter on a tripod at the right projects a horizontal laser plane across the field. A receiver on a mast attached to the scraper reads the beam. A control box in the tractor cab receives the signal and drives a hydraulic cylinder that raises or lowers the scraper so uneven ground on the left is cut and filled to the flat target grade. Target grade Uneven ground ahead Laser reference plane Control box Hydraulic valve + scraper Receiver Transmitter
Schematic, not to scale Travel direction ←

Editor This shows how a standard tractor-mounted laser leveling system works. Confirm that AMALASER's component names and control sequence match before launch.

03 Products & specifications

The AMALASER system.

Each system is built around four core components and matched to your tractor, scraper and fields. Model names and specifications are being finalised.

  • A rotating laser transmitter on a tripod in a tilled field. Illustrative image
    Sets the reference

    Laser transmitter

    Tripod-mounted rotating laser that creates the level or sloped reference plane.

    Model
    name
    Working range
    radius
    Accuracy
    value
    Slope capability
    single / dual
    Power
    battery
  • A laser receiver with indicator lights mounted on a steel mast above a scraper blade. Illustrative image
    Measures the blade

    Laser receiver & mast

    Mounted above the scraper, it detects the beam and reports the blade's height relative to grade.

    Model
    name
    Reception angle
    value
    Mast
    type / height
    Connection
    cable / wireless
  • A rugged control box with grade indicator lights mounted inside a tractor cab, looking out over a field. Illustrative image
    Decides & displays

    In-cab control box

    Shows the operator the blade position and sends correction signals to the hydraulic valve.

    Model
    name
    Modes
    auto / manual
    Display
    type
    Supply voltage
    value
  • Moves the blade

    Hydraulic valve kit

    Connects the control box to the tractor's hydraulics to raise and lower the scraper.

    Model
    name
    Hydraulic type
    open / closed centre
    Flow & pressure
    values
    Scraper
    supplied / compatible

Not sure which configuration fits? Tell us your tractor, scraper and field size and we'll recommend a complete system with a written quote.

Get a configured quote

04 Applications

Made for fields that run on water.

Laser leveling matters most where water moves across the surface. These are the jobs AMALASER is designed for.

  • Aerial view of flooded rice paddy basins with an even, mirror-like water surface. Illustrative image

    Rice & paddy basins

    The need
    The need: A uniform water depth across each basin, without deep hollows or exposed high spots.
    How AMALASER helps
    How AMALASER helps: Levels each basin to a flat plane so standing water sits evenly from bund to bund.
  • Irrigation water flowing down long straight furrows in a prepared field at sunrise. Illustrative image

    Surface & furrow irrigation

    The need
    The need: Water that advances steadily down every furrow or border, reaching the tail end without overwatering the head.
    How AMALASER helps
    How AMALASER helps: Sets a consistent, controlled grade along the run so flow is predictable across the field.
  • A tractor with a drag scraper grading a broad field to a gentle, uniform slope. Illustrative image

    Slope & drainage grading

    The need
    The need: A gentle, even fall that sheds surplus water instead of leaving it to stand on the crop.
    How AMALASER helps
    How AMALASER helps: Works to a sloped reference plane so the whole field drains in the direction you choose.

Who we work with

  • Farmers & growers
  • Land leveling contractors
  • Irrigation & land development projects
  • Agricultural dealers

05 Why AMALASER

Equipment is half the job. Support is the other half.

A leveling system has to work on the day you need it. Here is what AMALASER offers beyond the hardware.

  • Installation & setup

    Describe installation offer, e.g. fitting to the customer's tractor, hydraulic connection, first calibration

  • Operator training

    Describe training, e.g. on-farm session, what's covered, any written guides or videos

  • Service & spare parts

    Describe servicing, repair turnaround and parts availability

  • Coverage & local support

    Regions served, service partners and how customers reach support

Editor Only list services AMALASER actually provides. Remove any pillar that doesn't apply rather than leaving it vague. Warranty terms belong here once confirmed in writing.

06 See it working

Close-up of a laser transmitter glowing red on a tripod at dusk. Illustrative image

Don't take our word for it. Watch it work.

The best proof is your own ground. Book a demonstration to see the system set up and leveling soil, and get your questions answered in the field.

  • See the transmitter set up and the grade established
  • Watch the blade respond to the laser in real time
  • Ask about compatibility with your tractor and scraper

confirm demo format, regions & any cost

Book a Demo

07 Frequently asked questions

Questions before you buy.

Straight answers on compatibility, setup and support. If yours isn't here, ask us directly.

Will AMALASER work with my tractor?

A laser leveling system connects to your tractor's hydraulics to control the scraper, so compatibility depends on your hydraulic setup and power supply.

Requirements: minimum hydraulic flow / pressure, remote valve, electrical supply

Include your tractor make and model in the enquiry form and we'll confirm compatibility before you commit.

Do I need a specific scraper or bucket?

State whether AMALASER supplies scrapers, which existing scrapers can be fitted, and any mounting requirements

If you already own a scraper, tell us its make and width and we'll advise.

How long does setup take in the field?

Each job starts by positioning the transmitter, setting the grade and checking the receiver height on the scraper. Typical time: minutes per setup

First-time installation on a tractor: duration & who carries it out

Is it difficult to operate?

The operator drives while in-cab indicators show the blade position against grade, so leveling no longer depends on judging the surface by eye.

Training provided, e.g. on-farm session at handover

What maintenance does the system need?

Manufacturer maintenance guidance: cleaning, battery care, storage, calibration checks and recommended intervals

What service and support is available after purchase?

Support channels, service locations, repair turnaround, spare parts and warranty terms

Do you deliver to my area?

Delivery regions, lead times and installation coverage

Add your location to the enquiry form and we'll confirm delivery and installation options for you.

How do I get a price?

Pricing depends on the configuration your tractor, scraper and fields need. Request a quote with a few details and we'll come back with a recommended system and price.

payment / finance options, if offered

08 Enquire

Tell us about your fields.

Request a quote, book a demonstration or ask a question. It takes about two minutes.

  1. We review your detailsYour tractor, scraper, location and the job you have in mind.
  2. We get in touchA specialist contacts you to confirm requirements.
  3. You get a clear next stepA configured quote, a demonstration date or a straight answer.

Prefer to talk?

Phone
phone number
Email
email address

Fields marked with an asterisk are required.

I'd like to

Please enter your name.

Please enter a phone number we can reach you on.

Please enter a valid email address, e.g. name@farm.com.

Town or district, and country

Please tell us where the work is.

Application

Please choose the closest application.

e.g. 40 acres or 15 hectares
Your scraper, soil, timing or anything else that helps us prepare.

We use your details only to respond to this enquiry.

Request a Quote